DO NOT CONTAMINATE WATER, FOOD,
OR FEED BY STORAGE OR DISPOSAL:
DISPOSAL:
1. Rinse the emptied container thoroughly and add the rinsings to the spray mixture in the tank.
2. Follow provincial instructions for any required additional cleaning of the container prior to its disposal.
3. Make the empty container unsuitable for further use.
4. Dispose of the container in accordance with provincial requirements.
5. For information on the disposal of unused, unwanted product and the cleanup of spills, contact the Provincial Regulatory Agency or the Manufacturer.
NOTICE TO USER: This control product is to be used only in accordance with the directions on this label.
It is an offense under the Pest Control Products Act to use a control product under unsafe conditions.
DIRECTIONS FOR USE: It is a violation of federal law to use this product in a manner inconsistent with its labeling.
For Interior Use: Beams, girders, struts, supports and other places where birds can sit or roost.
1. Machinery, floors, etc. should be covered to prevent JT EATON'S "4 the Birds®" Bird Repellent Liquid from falling on them during application.
2. Surface being treated must be clean and dry to assure adhesion of repellent.
3. Clean by wiping or scraping dust, dirt, loose paint, droppings, nests, etc., from the surfaces being treated.
4. Do no dilute JT EATON'S "4 the Birds®" Bird Repellent Liquid with water or other solvents. Use as is.
5. Spray to the point of "runoff". Spray in such a way that the top surfaces of beams, girders, etc. are coated. This would necessitate the applicator to be level with or above the treated surfaces during application. Apply with any hand or pressure spray gun which has a discharge pressure of more than 40 P.S.I (275.79 kPa) and less than 150 P.S.I. (1034.2 kPa).
6. Surfaces difficult to cover by spraying, should be treated by applying JT EATON'S "4 the Birds®" Bird Repellent Liquid with a paint brush.
7. Cleaning: Repellent can be removed from interior surfaces and painted surfaces, with mineral spirits, naphtha or powder type cleaning agents. Repellent can be removed from concrete, tile or stone surfaces by hosing with water. However, this should be done within a very short time period after the area has been sprayed. Application equipment should be cleaned with mineral spirits after each use.
For Exterior Use: Trees, bushes, shrubs, vines, etc. It is not recommended for use on exterior surfaces of buildings or structures since stain or residue will result.
1. Any surfaces below or near the area to be treated that you do not want coated with this sticky material should
2. EATON'S "4 the Birds®" Bird Repellent Liquid
should be applied to the point of "runoff' to the top side of all branches large enough to support a bird.
3. Do not dilute JT EATON'S "4 the Birds®" Bird Repellent Liquid with water or other solvents. Use as is.
4. Applications can only be made with hand or pressure spray guns which can generate sufficient pressure, up to 150 P.S.l. (1034.2 kPa), to move the material to the desired treatment site. Keep material agitated. Not for aerial application.
5. It is recommended that treatment to trees, bushes, and shrubs be made in the fall or early spring when limbs are bare and easily accessible. When used as directed, JT EATON'S "4 the Birds®" Bird Repellent Liquid will neither harm trees and other vegetation or cause phytotoxicity to foliage.
6. Spraying should be done when temperatures are 5°C or above. Drift can be minimized or eliminated by
applying during calm conditions.
7. The amount of coverage you can expect is dependent on type of tree, bush, or shrub you are treating, spray equipment and number of and size of branches treated. Generally, 3.785 Liters JT EATON'S "4 the Birds®" Bird Repellent Liquid is sufficient to treat an average tree with a 12.70 cm diameter trunk, after foliage has fallen, or approximately six (6) 9.14 cm high shrubs. These coverage approximations should be used only as a guideline.
8. Cleaning: The tackiness of the Bird Repellent can be removed from wood or stone surfaces, such as
sidewalks, by hosing with water, if done very shortly after spraying. Repellent can be removed from all surfaces with mineral spirits, naphtha or powder type cleaning agents. Application equipment should be cleaned with mineral spirits after each use.
CAUTION: Do not apply material to trees or vines that are in bloom or bearing fruit.
NOTE: Do not spray directly on birds. Do not apply at locations where the user has concern that desirable birds may become entangled in the product. Avoid contamination of food or livestock feed.
NOTICE TO BUYER: Seller's guarantee shall be limited to the terms of the label and that subject thereto, the buyer assumes any risk arising out of the use or handling of the product.
First Aid: If on skin remove with a solvent such as mineral spirits then rinse with plenty of water. If in eyes immediately flush with plenty of water and get medical attention if irritation persists. If swallowed call a physician or poison control center immediately.
ENVIRONMENTAL HAZARDS
Do not apply to surfaces where small protected
bird species may become entrapped by this tacky repellent. Use only in conformity with Federal Migratory Bird Treaty Act Regulations.
J.T. EATON & CO., INC., Twinsburg, OH 44087 and "4 the Birds®" is a registered trademark of
BIRD CONTROL INTERNATIONAL, Macedonia, OH 44056
Made and Printed in the USA ©1999